When trying to resolve a complaint, code or no-start/no-crank condition on a stop/start vehicle, it is essential to know how the system operates. The problem may not have a complicated reason – something simple may be causing the stop/start system not to work.
The greatest obstacle to the advancement of stop/start technology is the driver’s and technician’s lack of trust in and knowledge of the technology. Many older drivers and technicians fear that stopping and starting the engine will cause a shorter life for the battery, starter and engine. But the real fear is that the engine will not start again at a green light.
Stop/start technology is more than just a switch wired to the brake pedal and starter – it is a function of the power management system that uses several modules to decide when the engine needs to stop and start.
On all stop/start vehicles, the life and performance of the battery are measured by the vehicle in several ways. These constant checks prevent the engine from being stopped and the battery not having the power to restart. Some manufacturers call it a battery or power management system but whatever its name, the goal of the system is to balance the load on the alternator and battery. Most of all, these monitoring steps prevent the customer from being stranded.
Most stop/start systems can use current-measuring sensors in the battery cables and will look at the electrical loads on the vehicle. Some more advanced systems will have connections on the positive and negative battery terminals that measure the internal resistance.
All systems also look at voltage drop during cranking. If the voltage drops too low or for too long, it will set a code and turn on the battery light in the instrument cluster.
Most systems use sensors to measure the temperature of the battery. Sensors can be on or inside the battery and some systems have the temperature sensor in the positive battery cable. If the engine control module is mounted near the battery under the hood, the temperature sensor in the module will be used to estimate battery temperature.
With a scan tool, it is possible to see data PIDs that indicate the life of the battery and the outputs of the sensors related to the condition of the battery. Some codes can be set for the battery and the sensors and also have monitors and parameters.
Don’t just use a voltmeter to determine the state of charge: voltage readings can be different for AGM batteries. Due to differences in internal construction, AGM batteries have lower internal resistance when compared to a conventional lead-acid battery. AGM can charge faster and recover faster after starting the engine. Also, AGM batteries perform better at colder temperatures.
More sophisticated battery testers can take these internal engineering features into account. Some vehicles use a second battery to handle non-starter loads, so the occupants don’t notice any disruption to the HVAC or audio systems when the engine is off.
Never take a new battery for granted. Often customers will install a battery on their own or have a battery replacement performed at retail auto parts or “big box” store. The battery may fit, but it will likely be a conventional flooded battery instead of an AGM or the specification for cold-cranking amps or reserve capacity will not match the vehicle. If you see a new battery, test it and make sure it is the correct battery for the application.
You may not think that the HVAC system would be connected to a stop/start system on a vehicle, but even a cabin temperature sensor can deactivate a stop/start system. All stop/start systems are designed so as not to inconvenience the occupants of the vehicle by causing the interior to be too hot or too cold.
If the vehicle is not up to temperature, the system will not stop the engine. Part of this is for emissions, but also to prevent the occupants from freezing on a cold day. On warmer days, it will not stop the engine if the air conditioning is set to a high setting. Also, if the engine is stopped, the system will compare the cabin and air duct temperatures to determine if the engine needs to be started to keep the cabin cool.
One of the unfortunate side effects of stop/start technology is that evaporator cores are becoming more insulated and evaporator fin and tube designs are continually changing.
Structure and Control
Once you begin looking at a stop/start system wiring diagram, you start to see a pattern. Under the hood, you will see a power distribution module that feeds other components and modules on the vehicle. Ford may call its a Smart Junction Box and Chrysler calls its the Totally Integrated Power Module. At first, these were simple modules that controlled the alternator and battery charging. Most contain the relays and some of the larger fuses.
The power control module might have connected to the vehicle with a simple LIN, SCP or UART network. On some late-model vehicles with a stop/start system, the module connects to the vehicle with a faster CAN-Bus network.
The power control module is now responsible for detecting and managing loads on the alternator and battery. On stop/start vehicles, the power control module works with other modules to control when and if a stop/start event happens. The modules will share information like speed and brake pedal position from the ABS module and HVAC information from the body control module.
High-end stop/start systems use a large generator/motor combo between the engine and transmission to turn the engine and generate power. But, the majority of systems are using a starter that looks a lot like a conventional starter.
These starters operate the same way but with some critical internal differences. The first thing you will notice is that the gear on the starter is larger and the gear reduction system is lower. This allows the starter to turn slower, this reduces wear on the brushes and bearings. Also, the armature and bushes are upgraded to improve the longevity of the starter.
You might have noticed when you pull up to a stoplight, some cars are silent. As the light turns green, you hear starters engage, engines start and see people pulling away. Like it or not, you will be working on a stop/start system at your shop as more vehicles with this technology see their warranties expire.