Key Programming Challenges And Opportunities

Key Programming Challenges And Opportunities

For most vehicles today, it's not so much about programming a new key to the car, but programming the car to the key.

Three situations might require key programming capabilities at your shop. First, being able to diagnose and program keys can be a tool as part of some no-start diagnostics. Second, you may run into a situation where a key or fob needs to be reprogrammed to the vehicle if a module was replaced. Third, a customer might want an extra key, or all the original keys were lost.

You might think that key programming is a job for a locksmith or specialist, but the market is changing. Brick and mortar locksmith and dealership parts departments can cut key blanks, but it is up to you to make them work with the vehicle. In the case of some proximity keys, there is no key to cut – it is all up to you.

For most vehicles at your shop, it is not as much about programming a key to the car, but programming the car to the new key. Programming a vehicle to the key might require a procedure to put the vehicle into a learn mode; this is typically called “onboard” programming.

Newer vehicles require a scan tool to learn a new key or remote to perform onboard programming. You might already do this at your shop if you have the right scan tool and software.

Onboard procedures use the antenna coil on the vehicle to read the transponder or ID number in the new key or remote. The vehicle gets the key’s transponder to transmit, and the unique ID is learned by the vehicle during the procedure.  

PIN CODES

One of the changes made to some late-model vehicles is the requirement to have a three- or four-digit PIN code to perform onboard programming. This code resides in the module for the immobilizer system. 

You can contact the OEM for the code, or, in some cases, it might be found in the owner’s manual if you are lucky. But, some key programming tools can harvest the PIN code from the modules. VW and other makes require PIN codes, depending on specific model years.

PROGRAMMING KEYS

To increase security, some OEMs are requiring the key to transmit more than just the ID code. VW and other European manufacturers are requiring that the key transmits the unique VIN of the vehicle. Specialty key programming tools can program the transponder code and VIN onto a key.  

REFLASHING AND REPROGRAMMING

Data can go both ways when it comes to some key programming tools. Information from a key can be programmed into a module, or information from an existing model can be programmed onto a key. This tool function can save you if a module has been replaced or reflashed and the key information is lost. It is also helpful if you are in a situation where all the keys have been lost. 

For situations like this, you have several options. Some key programming tools and vehicles will allow you to clone key transponders in the memory of the vehicle. The key programming tool communicates with the vehicle to find the information about the existing keys, and then burns that code to a new transponder using a specialized attachment for the key. It may call for reflashing completely new transponder codes to a module. For some cars, this can be performed through a J2534 interface. Other cases may require the module or EEPROM chip to be removed for reprogramming.  Specialized key programming tools let you do it at your shop. 

The key and fob for modern vehicles are more than a key. They can start a vehicle remotely, open a rear hatch with a swipe of a foot, and make sure the vehicle is secure against physical and virtual attacks. If you are already servicing these vehicles, you can’t avoid key programming.

You May Also Like

When Small Animals Cause Big Problems With Cars

Sure, they’re cute on TV, but critters can inflict serious punishment on your customers’ vehicles.

We all have a cache of stories involving weird, wacky and downright strange customer service requests, but the majority of them can be traced back to mechanical failure and/or human error.

You may be familiar with “Just Rolled In,” a YouTube channel highlighting some of the most terribly maintained and unsafe vehicles brought into shops across the country, along with strange “customer states … ” complaints that must be seen to be believed. While the worst damage is due to lack of maintenance and misguided DIY repairs, sometimes there’s no one to blame but Mother Nature.

Customer Service – How Brakes Affect Fuel Economy

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

BMW Infotainment System Service Tips

Even the most sophisticated systems can encounter issues.

Ride Control Diagnostics From Tire Wear Patterns

Learning how to read the tire and communicate your findings is the key to safe and effective ride control service.

Explaining Why A Customer’s Car Leaks Oil

Service advisors, explain that there are a few common causes for the majority of oil leaks on the road.

Other Posts
Ball Joints – How To Avoid Memory Steer

Follow all instructions to avoid issues caused by incorrect installation. This video is sponsored by Auto Value and Bumper to Bumper.

Understanding The Evolution of Modern Driveshafts

Learn about modern driveshafts. This Shop Owner Solutions podcast is presented by TrakMotive.

Bosch Auto Service Announces Tekmetric Collaboration

Service Franchisees receive exclusive access to Tekmetric’s software suite and customized training for seamless integration.

Forvia Hella Celebrates its 125th Anniversary

Forvia Hella is now a global automotive supplier with approximately 37,500 employees at over 125 locations worldwide.