Top Ten Wheel Bearing Torque Tips -

Top Ten Wheel Bearing Torque Tips

A torque wrench is an essential tool when it comes to installing wheel bearings. Here are the top 10 tips to remember about these tools and procedures.

  1. CHECK THE RECOMMENDED TORQUE PROCEDURES AND SPECIFICATIONS
    It is nearly impossible to give a general torque specification or range for a wheel bearing axle nut. There can be significant differences, depending on bearing type and housing. Always check the service information for the correct procedure.
    Hub units can require many steps to set the final torque of the axle nut. On some hub units with factory-set preload, the axle nut might only secure the stub axle in the bore. On other hub units, the final adjustment is setting the load paths for the races and rolling elements. The torque specifications depend on the size of the bearings, the diameter of the axle and many other factors like the style of axle nut.
    Wheel bearing manufacturers may use a different style nut that is included with the bearing. This nut may have a different torque specification – lower or higher – than the value listed in the service information. Some manufacturers will include this information in the box.
    Even if you are installing a set of tapered roller bearings, it pays to look at the service information. Not all procedures and specifications are the same, and the method you learned from school or from your father might not work on some vehicles.
  1. IF IT SAYS “ON THE GROUND,” DO IT ON THE GROUND
    Many vehicles require the wheels to be on the ground for the final torqueing of the axle nut to specifications. This ensures the proper mating of the split inner rings of the bearing needed to achieve the proper internal clearances. However, jamming a screwdriver in the fins of the rotor and bracing it against the caliper bracket might not achieve the same results. For specific instructions, refer to the vehicle manufacturer’s service information.
  1. USE A NEW NUT / Cotter Pin*
    Some hub units and wheel bearing sets come with a new nut in the box. This is because the nut deforms to secure the hub unit to the axle. In these applications, a new nut must always be used when installing a hub. Reuse of the old nut could potentially cause the nut to loosen during vehicle operation.
  1. CLEAN THE AXLE SHAFT BEFORE INSTALLATION
    Clean and inspect the axle shaft before installing a new hub assembly. Use a fine file, wire brush, emery cloth or honing stone as appropriate to remove any debris, nicks or burrs from the splines. You can apply a light coating of oil to the splines. But don’t use any lubricants on the threads or washers. This can reduce friction on the threads and cause the nut to be over-torqued.
  1. DON’T USE YOUR TORQUE WRENCH AS A SOCKET WRENCH
    Use a torque wrench to apply a specific torque value during the final assembly process. Do not use a torque wrench as the primary means of tightening or loosening fasteners. Also, wind down the torque wrench before you put it back in your toolbox.
  1. DON’T USE AN IMPACT
    While it may appear to be easier to use an impact wrench, it is not recommended. OEM and bearing manufacturers always recommend using a torque wrench for installation. Using an impact to “run down” the axle nut can cause the assembly to be over-torqued. However, during removal, it is possible to use an impact. First, loosen the axle nut with a breaker bar if possible. Using this method can prevent causing damage to the stub axle or CV joint.
  1. REPLACE A DAMAGED WHEEL HUB FLANGE BEFORE ASSEMBLY
    When replacing a press-type wheel bearing and hub flange, it’s important that all the wheel-end parts properly work together after reassembly. A hub flange with damage to the shoulder the makes contact with the inner bearing can cause inconsistent torque values and lead to failure down the road. Wheel Hub flanges for most applications are available for many sources.
  1. DO YOU TRUST YOUR TORQUE WRENCH?
    For some hub units, the final torque specification can range from 150 to 350 ft/lbs depending on the application. Accurately tightening nut is critical to set the load paths for the bearings. But you must trust your torque wrench.
    Torque wrenches designed for lug nuts typically have an upper limit of 190 to 200 ft/lbs. Even if the final torque for a hub unit is 185 ft/lbs, you could be at the limits of accuracy for your torque wrench. A torque wrench is most accurate in the middle, and almost every torque wrench is least accurate to the ends of its scale range of the wrench. So if the final torque is 200 ft/lbs, you would be better off using a torque wrench with 300 ft/lbs limit.
    How do you determine if your torque wrench is accurate? Some tool trucks have a torque wrench tester that can help spot a torque wrench that is malfunctioning. You need to test at least several torque settings, including the highest and lowest settings. It is not uncommon to find a wrench that will be accurate at 50 ft./lbs., but significantly inaccurate at 25 or 150 ft./lbs. If the accuracy is off, you should send it out to be calibrated rather than buy another torque wrench.
  1. USE AXLE NUT SOCKETS
    Axle nuts typically are recessed into the flange. The nut will normally be 29mm or larger and can be a six-point or 12-point hex. In some cases, the axle will protrude, preventing the use of a shallow socket. Tool manufacturers make sockets that are specific to axle nuts.
    Using these sockets can prevent a comeback and damage to the nut. They can also increase torque wrench accuracy by fully engaging the nut.
  1. DON’T FORGET THE OTHER TORQUE SPECIFICATIONS
    Most hub units are held to the suspension knuckle using three or four fasteners. These fasteners have their own torque specifications and procedures. Some of these fasteners are torque-to-yield and can’t be used a second time because they have stretched. Also, some fasteners use thread-locking compounds that must be removed and reapplied.

You May Also Like

UTILIZE YOUR MARKETING TOOLS – A Plan to Find Good Technicians 

Do your recruiting methods have you scratching your head, wondering why you can’t find or keep good technicians? Maybe it’s time to take a step back and utilize your sophisticated marketing tools to grow your business. STAND OUT AND GET FOUND ONLINE Your website is one of the first impressions determining how a customer views

Do your recruiting methods have you scratching your head, wondering why you can't find or keep good technicians? Maybe it's time to take a step back and utilize your sophisticated marketing tools to grow your business.

STAND OUT AND GET FOUND ONLINE

Your website is one of the first impressions determining how a customer views your shop. And, it's no different for technicians looking to come to work there. It's just as crucial for your website to be attractive and SEO optimized as your shop to be clean.

Hybrids and CVTs: Nissan RE0F03H (JF019E)

The Background Beginning with the 2017 model year, Nissan introduced a hybrid version of the Rogue with the RE0F03H CVT transmission behind a 2.0 L engine. Infiniti also produced a hybrid version of this transmission in the QX60 behind a 2.5 L engine. The Jatco designation for this transmission is the JF019E, which is a

How Lease-to-Own Financing Can Boost Your Bottom Line

It’s a common scenario for many tire dealers: a customer is shopping for a new set of tires but doesn’t have all the funds on hand to pay for the purchase upfront. You may try to resolve this by offering your own in-store credit option. But by going this route exclusively, you could miss out

Closing Tool for Recommended Repairs Goes Digital

Your customer clicks on the link your service advisor just texted. The updated repair order at the end of the link confirms her worst fear: Your technician’s repair recommendations cost more than what’s in her bank account and all but eliminates whatever’s left on her high-balance credit card. That’s when she spots a button in

How To Get and Retain Customers: A Growing Shop Story

You want your shop to be successful. WE want your shop to be successful. Now that we’ve got that figured out, let’s break down how we can make that happen. Spoiler alert: it all comes down to your customers. Who should you be looking for when it comes to customers? You may be thinking, “Well,

Other Posts

SKF Vehicle Aftermarket Extends Auto Hub Warranties 

SKF says the expanded full warranty covers the company’s complete lineup of premium auto hub components.

Replacing Tesla Wheel Bearings

Good news – servicing the hub unit on a Tesla is the same as with many traditional cars and light trucks.

Women At The Wheel Podcast, Ep. 1: NTN’s Georgianne Dickey (VIDEO)

The Women at the Wheel podcast series kicks off with Georgianne Dickey, director of Marketing for NTN Bearing Corp.

New AMN Women at the Wheel Podcast Kicks off This Week

The new series kicks off July 20th with Georgianne Dickey, director of marketing for NTN Bearing Corp. of America.