What Impacts Catalytic Converter Efficiency? Many Things... -

What Impacts Catalytic Converter Efficiency? Many Things…

You may be surprised at the tiny details that can affect and limit the life of a catalytic converter.

Almost every part on the engine determines how long a catalytic converter will last. It could be a faulty line of computer code that pulses an injector too long, or a stuck piston ring that allows oil to be sucked into the combustion chamber. Little details such as these can limit the life of a catalytic converter.

Platinum, palladium, rhodium and cerium store oxygen in the converter during periods of lean operation or by an external air source. The oxygen is used to oxidize hydrocarbons and toxic gases during periods of “rich” operation. This oxidation changes harmful carbon monoxide (CO) into carbon dioxide (CO2). It will also oxidize hydrocarbons or fuel by turning them into inert carbon products and water (H2O). This is called a “reduction” in chemistry, or the breaking down of molecules into smaller parts. The precious metals act as catalysts in the process and are not changed; they just store and use oxygen to break down combustion products.

However, they can’t break down or oxidize some chemicals in the exhaust stream. If the catalyst is blocked by carbon, silica or phosphorus, the converter will fail to work.

For a catalyst efficiency code to be set, a number of criteria must be met. For example, the oxygen or air/fuel sensor and the rear oxygen sensor must see a reduction in the efficiency of the converter. In other words, if the oxygen levels before and after the converter do not change, the converter is not working. The specific enabling criteria are different for almost every vehicle.

But, this is not an automatic pass or fail. The oxygen sensors need to see this loss in efficiency over a number of drive-cycle conditions. This is why it might take a few hours or even a few days for the light to come back on after an efficiency code is erased and no other service is performed.

On most vehicles, an efficiency code will not be set if an oxygen sensor heater code or any oxygen sensor-related code is set. The same is true for coolant and air temperature sensors. You could repair these items, only to have the customer come back with the check engine light on and an efficiency code that has been set.

What is Efficiency?

The converter has an efficiency rating that is computed by the vehicle. This number rates the amount of reduction that is occurring in the converter and its ability to store oxygen. But, the efficiency of the converter is tied to the fuel trim of the engine. Most engines minutely alter the fuel trim to replenish the oxygen in the converter and to add fuel for reduction. This helps to keep the converter at the correct temperature to achieve the most efficient operation.

If an engine is running too rich, it cannot store oxygen. If it is running too lean, the reduction process might not occur due to an inability to heat up.

If the engine is dealing with a leaking vacuum hose or a stuck injector, it can’t switch the fuel mixture properly to replenish oxygen and reduce harmful contaminants.

Converter efficiency, along with the switching between rich and lean, can be checked with some scan tools. Lab scopes can also be used to monitor the switching process. The converter efficiency threshold of a vehicle is part of a vehicle’s software. Once the efficiency drops below a specified level and other criteria are met, an efficiency code will be set. The software is designed to filter out data that may be erroneous, or random signals that may interfere with the oxygen sensor.

Most converters start out at about 99 percent efficiency when new, and quickly taper off to about 95 percent efficiency after about 4,000 miles. As long as efficiency doesn’t drop off more than a few percentage points, the converter will do a good job of cleaning up the exhaust. But, if efficiency drops much below 92 percent, it will usually turn on the MIL lamp. With vehicles that meet the tougher LEV (Low Emission Vehicle) requirements, there’s even less room for leeway. A drop in converter efficiency of only 3 percent can cause emissions to exceed federal limits by 150 percent. The LEV standard allows only 0.225 grams per mile of hydrocarbons, which is almost negligible.

You May Also Like

Solving BMW Laser and LED Exterior Lighting Issues

Many complaints are that the lights aren’t as bright as before, or there is a warning in the driver information center.

BMW has been using LEDs for exterior lighting for decades. The first applications were for the third brake light for sedans. LEDs extended the life of the light, so no technician would have to lower the headliner to access the bulbs. Other LED innovations included the round halo lights that almost every young BMW enthusiast tried to fit to their older BMWs and non-BMWs.

Ignition System Tests You Should (And Shouldn’t) Follow

Do your technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module?

ADAS Technology and Vehicle Alignment

ADAS and autonomous features rely on the alignment being exactly to OEM specifications to perform correctly.

Repairing Wiring Harnesses

We explore the basics of probing and poking.

Top 10 ADAS Calibration Tips

You may have done alignments for years – but are you certain you’re meeting ADAS alignment requirements?

Other Posts

Read ShopOwner’s March Edition Online Now

ShopOwner includes valuable business management and technical editorial content.

Vehlo Acquires Shop Management Software, Shop-Ware

Shop-Ware is a cloud-based shop management platform for independent repair shops.

How Important is Regenerative Braking For EVs?

Regenerative braking helps to increase the range of an EV by up to 20%.

Applications Open for Federated Car Care Scholarships

Completed applications due to AutomotiveScholarships.com by March 31.